advisory

Get best price

Belt Conveyor Deenergized

  1. Home
  2. Belt Conveyor Deenergized
  • belt conveyor deenergized mepsystemfr

    Belt Conveyor Deenergized Mepsystemfr

    The belt conveyor was not deenergized and locked out and tagged out before the victim performed work Corrective Action Management developed a standard operating. Live

  • Accident Report Detail Occupational Safety and Health

    Accident Report Detail Occupational Safety And Health

    Sep 17, 2009 The belt conveyor was initially deenergized by the coworker and a guard removed to allow an adjustment to be made. The removing of the guard exposed a chain and sprocket drive which also had a grease fitting. After the adjustment was made, the conveyor was energized so it could be checked. The coworker turned the conveyor off but did not ...

  • Final Report Fatality 18 October16 2010 Mine

    Final Report Fatality 18 October16 2010 Mine

    The belt conveyor was not deenergized and blocked against motion before persons removed spillage. Additionally, the procedures for starting the belt conveyor did not ensure that persons were protected. ENFORCEMENT ACTIONS. Order No. 6459094 was issued on October 16, 2010, under the provisions of Section 103(j) of the Mine Act. This order was ...

  • Final Report Fatality 1 February 01 2014 Mine

    Final Report Fatality 1 February 01 2014 Mine

    Feb 01, 2014 The belt conveyor was not deenergized and locked out and tagged out before the victim performed work. Corrective Action Management developed a standard operating policy (SOP) regarding the belt conveyors cleanup and maintenance, as well as a detailed lock-out/tag-out policy that requires persons to deenergize the equipment and ensure the ...

  • 1926961 Deenergizing lines and equipment for employee

    1926961 Deenergizing Lines And Equipment For Employee

    Conductors and parts of electric equipment that have been deenergized under procedures other than those required by this section shall be treated as energized. 1926.961(b) General. 1926.961(b)(1) System operator. If a system operator is in charge of the lines or equipment and their means of

  • MSHA Coal Mine Fatal Accident Investigation Report

    Msha Coal Mine Fatal Accident Investigation Report

    The draw-off belt conveyor was operating and coal was being conveyed to a bin which was being used to load trucks. The feeders are not designed to deliver coal by gravity when deenergized. There are no gates or other devices to prevent gravity flow of material.

  • MSHA Coal Mine Fatal Accident Investigation Report

    Msha Coal Mine Fatal Accident Investigation Report

    Power to the collecting belt conveyor drive motor was deenergized, locked and tagged out by Jerry Collins, Mechanic, to prevent accidental movement of the belt flight while repair work was being performed. The 300 vdc electric bonder and 575 vac arc welder had been modified to be used as a cutting tool instead of a welding tool.

  • MSHA Metal Nonmetal Mine Safety and Health

    Msha Metal Nonmetal Mine Safety And Health

    Dec 21, 2012 Corrective Action Management established policies, procedures, and controls to ensure that belt conveyors were deenergized, locked and tagged out, and blocked against hazardous motion before persons work on them. Management also installed grease lines that could be reached from the ground. A man-lift has also been provided to provide safe access.

  • Virginia Department of Mines Minerals Energy

    Virginia Department Of Mines Minerals Energy

    belt conveyor tailpiece, the belt crew deenergized this belt using the remote belt control switch - 8 - and proceeded to install a bottom belt scraper, that had previously been removed. While attempting to install the bottom belt scraper at this location, the belt crew determined that the belt

  • Inspection Detail Occupational Safety and Health

    Inspection Detail Occupational Safety And Health

    Oct 01, 2009 The belt conveyor was initially deenergized by the coworker and a guard removed to allow an adjustment to be made. The removing of the guard exposed a chain and sprocket drive which also had a grease fitting. After the adjustment was made, the conveyor was energized so it could be checked. The coworker turned the conveyor off but did not ...

  • 30 CFR 75323 Actions for excessive methane CFR

    30 Cfr 75323 Actions For Excessive Methane Cfr

    (a) Location of tests. Tests for methane concentrations under this section shall be made at least 12 inches from the roof, face, ribs, and floor. (b) Working places and intake air courses. (1) When 1.0 percent or more methane is present in a working place or an intake air course, including an air course in which a belt conveyor is located, or in an area where mechanized mining equipment is ...

  • Section 75323 Actions for excessive methane 30 CFR

    Section 75323 Actions For Excessive Methane 30 Cfr

    Apr 30, 2021 Apr 30, 2021 (1) When 1.0 percent or more methane is present in a working place or an intake air course, including an air course in which a belt conveyor is located, or in an area where mechanized mining equipment is being installed or removed- (i) Except intrinsically safe atmospheric monitoring systems (AMS), electrically powered equipment in the affected ...

  • Stop Powered Haulage Accidents Stay Alert Stay Alive

    Stop Powered Haulage Accidents Stay Alert Stay Alive

    Jul 14, 2021 Stay Alive This has been a difficult time for the mining community. So far this year, nine miners have been killed and 185 have been injured in accidents involving powered haulage equipment such as shuttle cars, scoops, locomotives, front end loaders and more. Year to date, this is the highest number of powered haulage fatalities since 2006.

  • Accident Report Detail Occupational Safety and Health

    Accident Report Detail Occupational Safety And Health

    Sep 03, 2010 The DDM Wave Feeder and the Reception Belt conveyor system were deenergized and locked out. The DDM Edger Chipper Multifunction line operators control panel was being used to maintain the log selector gate in an open position. The Log Selection Gate control switch was placed in the AUTO position on the control booth console.

  • Final Report Fatality 3 February 24 2011 Mine

    Final Report Fatality 3 February 24 2011 Mine

    Feb 24, 2011 The belt conveyor was not deenergized, locked and tagged out, and blocked against motion prior to persons removing tramp metal from the magnet. Additionally, the startup procedures for the belt conveyor did not ensure that persons were protected when it was started. The required audible warning device could not be heard above the plant noise.